Sew a little sparkle into your wearable project with an Adafruit LED Sequin. These are the kid-sister to our popular Flora NeoPixel, they only show a single color and they don't have digital control, but that makes them smaller easier to use for...

Our popular Raspberry Pi Ultimate Kits include an assortment of components for circuit building. These are very handy components, so we've made them available as a separate item :) Included Components 2 x RGB LED 2 x Red LEDs 2 x Green LEDs 2 x...

Split core current transformer are sensors that are used for measuring alternating current. They are particularly useful for measuring whole building electricity consumption (or generation for that matter). This Split core current transformer is...

This is the BC337, an NPN silicon BJT (Bipolar Junction Transistor). This little transistor can help in your project by being used to help drive large loads or amplifying or switching applications. The BC337 is specifically rated at 50V and 800mA max...

This is a very common signal diode - 1N4148. Use this for signals up to 200mA of current. Documentation Datasheet

These are high quality Single Pole - Double Throw (SPDT) sealed relays. Use them to switch high voltage, and/or high current devices. This relay's coil is rated up to 12V, with a minimum switching voltage of 5V. The contacts are rated up to 5A (@250VAC,...

What's better than a single LED? Lots of LEDs! A fun way to make a small display is to use an 8x8 matrix or a 4-digit 7-segment display. Matrices like these are 'multiplexed' - so to control all the seven-segment LEDs you need 14 pins...

Overview Protective Case for the 15.6inch FHD Monitor Features Dedicated protective case ONLY for use with our 15.6inch FHD Monitor Easy to install Whole body wrapped protection Folio cover stand, multi viewing angles Nice and...

An anemometer is a device used for measuring wind speed, and is a common weather station instrument. This well made anemometer is designed to sit outside and measure wind speed with ease. To use, connect the black wire to power and signal ground, the...

The SparkFun Soil Moisture Sensor is a simple breakout for measuring the moisture in soil and similar materials. The soil moisture sensor is pretty straightforward to use. The two large, exposed pads function as probes for the sensor, together acting as...

The long awaited BME680 from Bosch gives you all the environmental sensing you want in one small package. This little sensor contains temperature, humidity, barometric pressure, and VOC gas sensing capabilities...

This sensor can detect flexing or bending in one direction. They were popularized by being used in the Nintendo PowerGlove as a gaming interface. These sensors are easy to use, they are basically resistors that change value based on how much their...

This sensor can detect flexing or bending in one direction. They were popularized by being used in the Nintendo PowerGlove as a gaming interface. These sensors are easy to use, they are basically resistors that change value based on how much...

This is a highly integrated round-shaped all-in-one capacitive fingerprint sensor module, which is nearly as small as a nail plate. The module is controlled via UART commands, fairly easy to use. It's advantages includes 360° omni-directional...

This is a great general purpose-actuator for tiny mechanisms. The FS90 offers positive control over a 120 degree angle. Operating angle controlled by standard servo pulses between 900us and 2100us. Has a three wire connector for the power,...

A button is a button, and an LED is a LED, but this LED illuminated button is a lovely combination of both! It's a medium sized button, large enough to press easily but not too big that it gets in the way of your project panel. It has a built in LED that...

This thumbstick is an analog joystick - more accurate and sensitive than just 'directional' joysticks - with a 'press in to select' button. Since it's analog(10k potentiometers), you'll need two analog reading pins on your microcontroller to determine...

Material: PlasticColor: RedVoltage: 3A 125VLeads: Solder lugsContacts configuration: SPSTSwitch method: OFF / ON

This straight bar load cell (sometimes called a strain gauge) can translate up to 5kg of pressure (force) into an electrical signal. Each load cell is able to measure the electrical resistance that changes in response to, and proportional of, the strain...

This is an OLED display module, 1.5inch diagonal, 128x128 pixels, 16 gray scale, with embedded controller, communicating via SPI or I2C interface. Features 128x128 high resolution 16 gray scale, better display effect Supports SPI or I2C interface,...