8086 Consultancy

Pi (3A+/etc), camera, camera cable, PSU are not included. What is it? APlusCam is designed in the shape of a Raspberry Pi HAT with mounting holes for a Raspberry Pi Camera and suction cups...

Allows two HAT or pHAT (or a mix) to be attached to a single Raspberry Pi 40 way connector. All pins are connected *except* ID_SD and ID_SC (HAT EEPROM) which have solder jumpers - this allows HAT...

The Raspberry Pi camera module comes with its own 30cm cable to connect to the Pi, but sometimes that's simply not long enough. This lovely little board lets you add extension cables to your existing...

The Cluster HAT is the perfect tool for modelling, testing and teaching small scale clusters. The Cluster HAT is designed to interface a controller (Raspberry Pi A+/B+/2/3/4) with 4 Raspberry Pi...

USA customers: this product is also available at our USA store - PiShop.us The Cluster HAT is also available in a Cluster Kit (comes with 4 Raspberry Pi Zero W) The Cluster HAT interfaces a...

The ClusterCTRL Stack (controller and passive backplane) is a simple way to both power and control cooling for a stack of 5 Raspberry Pi. Controller Powered by 12-24V PSU. 20 pin header for...

Dual Supply for Raspberry Pi (A+/B+/2B/3B/3B+) Power from each Micro USB connector goes via a MOSFET "Ideal Diode" which is then connected directly to the Micro USB socket on the Raspberry Pi. Data...

Allows four HAT or pHAT (or a mix) to be attached to a single Raspberry Pi 40 way connector. All pins are connected, ID_SD and ID_SC (HAT EEPROM) have cuttable solder jumpers. For HAT/pHAT with an...

FOR USE WITH GIANT BUTTERFLY PCB Hardware Kit [ OPTIONAL ] The hardware kit includes everything  you need to mount the Giant Butterfly PCB on your Raspberry Pi and then mount up to four...

The I2C multiplexer allows connecting multiple I2C devices with the same address onto a single I2C bus (PCB colour may vary). For each multiplexed output there are 4 pins - data ports SDAx, SCLx GND...

The MMC HAT adds a second micro SD socket to your Raspberry Pi using the second SDIO interface. The MMC HAT has many uses including: Micro SD card reader. Write new images, repair or modify...

Using solderless pins the adapter slides onto the back of a Pi Zero GPIO (If a permanent connection is required the adapter can still be soldered to the GPIO header). The adapter PCB is printed with...

Connect your Raspberry Pi Zero or Pi Zero W directly to your computer for use as a USB Gadget device (USB Ethernet / Serial / Ethernet+Serial / etc.) or just for power. Works with all public...

The kit contains the following connector boards and pin headers. QtyTypeGender 2 Micro USB Male 2 Micro USB Female 2 USB Type-A Male 2 USB...

USB Serial Adaptor Plugs directly onto our Cluster HAT and MMC (SD) HAT to provide serial console access to the Raspberry Pi for quick access. Using jumper wires it can be used to access the serial...

USB to (3.3v) Serial adaptor for use with the Raspberry Pi with a pinout designed to plug straight onto Pi GPIO pins (26 or 40 pin). Its a low cost no fuss adaptor which uses built-in USB-CDC...

Enables power to a USB device to be turned on/off via a USB power switch (MOSFET). Configuration Supplied with the PD (pull down) resistor set (Normally off). Connectors on top for GND / EN /...

The adaptor allows the Raspberry Pi 4 to be used with a Pi USB-C power supply (or DC barrel jack) whilst allowing access to USB OTG data over a separate USB-C connection. USB Type-C (DATA POWER)...

The adaptor allows the Raspberry Pi 4 to be used with a Pi Micro USB power supply (or DC barrel jack) whilst allowing access to the OTG USB. USB Type-A (data and power) <> USB Data (Micro USB)...